16-2-17 zse ise pse z i se3 ps z i se 1 2 zsp isa2 is zsm pf2 if data series zse40/ise40 high precision, digital pressure switch how to order zse40 01 ise40 01 22 22 for vacuum/compound pressure for positive pressure 10.0 to ?01.3 kpa ?00.0 to 100.0 kpa set pressure range nil f ?.100 to 1.000 mpa f or positive pressure set pressure range nil unit specifications nil m with unit switching function note1) si unit only note 2) nil l lead wire length 0.6 m 3 m ? option npn open collector 2 outputs + analog output npn open collector 2 outputs + auto shift input pnp open collector 2 outputs + analog output pnp open collector 2 outputs + auto shift input input/output specifications 22 30 ? 62 ? 70 ? setting range ?00.0 to 100.0 kpa ?01.3 to 101.3 kpa ?.000 to 1.000 mpa set pressure range ?00.0 to 100.0 kpa 10.0 to ?01.3 kpa ?.1 to 1.000 mpa option nil a none bracket a (zs-24-a) b bracket b (zs-24-b) e p anel mount (zs-22-a) f p anel mount + front protective cover piping specifications 01: r 1/8 (with m5 female threads) t1: npt 1/8 (with m5 female threads) r 1/8, npt 1/8 m5 x 0.8 female threads ? m5: m5 x 0.8 (female threads) m5 x 0.8 ? c4: with ? one-touch fitting ? c6: with ? one-touch fitting w all mount wall mount ? option ?, ? one-touch fitting w1: rc 1/8 rc 1/8 reverse pressure two directions rc 1/8 f or vacuum pressure f or compound pressure note when equipped with auto shift function, the following ranges can be set. note 1) this will no longer be sold for use in j apan after the new weight and measure act is implemented (october,1999). note 2) fixed unit f or vacuum/compound pressure: kpa f or positive pressure: mpa (zs-24-c) ? when optional parts only are required, order with the part n umbers inside ( ). http://www..net/ datasheet pdf - http://www..net/
16-2-18 series zse40/ise40 specifications example of internal circuit and wiring rated pressure range operating pressure range/set pressure range withstand pressure set pressure resolution note 1) applicable fluid po w er supply voltage current consumption switch output repeatability hysteresis response time (with anti-chattering function) output short circuit protection display display accuracy indicator light analog output note 2) a uto shift input note 3) environmental resistance t emperature characteristics port size lead wire w eight zse40f (compound pressure) ?00.0 to 100.0 kpa ?00.0 to 100.0 kpa 500 kpa 0.1 0.001 0.001 0.02 0.01 1 0.1 air, non-corrosive/non-flammable gas 12 to 24 vdc 10%, ripple (p-p) 10% or less 55 ma or less npn or pnp 2 outputs max. load current : 80 ma max. applied voltage: 30 vdc (with npn output) residual voltage : 1 v or less (with 80 ma load current) 0.2% f.s. 1digit or less var iable fixed (3 digits) note4) 2.5 ms or less (with anti-chattering function: 24 ms, 192 ms and 768 ms selections) ye s 3 1/2 digit led display (sampling cycle: 5 times/sec.) 2% f.s. 1 digit or less (at ambient temperature of 25 3 c) green led (out1: lights when on), red led (out2: lights when on) output voltage: 1 to 5 v 5% f.s. or less (in rated pressure range) linearity: 1% f.s. or less output impedance: approx. 1 k ? no-voltage input (reed or solid state), input 5 ms or more ip65 operating: 0 to 50?c, stored: ?0 to 60?c (no condensation or freezing) operating/stored: 35 to 85% rh (no condensation) 1000 vac for 1 min. between lead wires and body 50 m ? or more (at 500 vdc) between lead wires and body 10 to 500 hz at the smaller of amplitude 1.5 mm or acceleration 98 m/s 2 (10 g) in x, y, z directions for 2 hrs. each (de-energized) 980 m/s 2 (100 g) in x, y, z directions 3 times each (de-energized) in a temperature range of 0 to 50 c, 2% f.s. or less of pressure measured at 25 c 01: r 1/8, m5 x 0.8, t1: npt1/8, m5 x 0.8, w1: rc 1/8 c4: with ? one-touch fitting, c6: with ? one-touch fitting, m5: m5 female threads 5-wire oil resistant heavy-duty cord (0.15 mm 2 ) 01/t1 types approx. 60 g, w1 type approx. 80 g, c4/c6/m5 types approx. 92 g (each including 0.6 m lead wires) zse40 (vacuum pressure) 0.0 to ?01.3 kpa 10.0 to ?01.3 kpa output voltage: 1 to 5 v 2.5% f.s. or less (in rated pressure range) linearity: 1% f.s. or less output impedance: approx. 1 k ? ise40 (positive pressure) 0.000 to 1.000 mpa ?.100 to 1.000 mpa 1.5 mpa 0.001 0.01 0.01 0.1 kpa mpa k g f/cm 2 bar psi mmh g inh g hysteresis mode enclosure ambient temperature range ambient humidity range withstand voltage insulation resistance vibration resistance impact resistance window comparator mode setting range ?00.0 to 100.0 kpa ?01.3 to 101.3 kpa ?.000 to 1.000 mpa set pressure range ?00.0 to 100.0 kpa 10.0 to ?01.3 kpa ?0.1 to 1.000 mpa note) when equipped with auto shift function, the following ranges can be set. note 1) equipped with unit switching function (types without the unit switching function use si units (kpa or mpa) only.) note 2) for zse40 (f)/ise40- - 22 62 note 3) for zse40 (f)/ise40- - 30 70 note 4) for zse40f (compound pressure) with ?si indication, this is 0.03 to 0.04 psi. note 5) for zse40f (compound pressure) with ?si indication, zero clear is in the r ange of 0.01 psi. main circuit load load 1 k ? 12 to 24 vdc dc (+) (brown) analog output (gray) out1 (black) out2 (white) dc (? (blue) main circuit 1.2 k ? 6.8 k ? load load 12 to 24 vdc dc (+) (brown) a uto shift input (gray) out1 (black) out2 (white) dc (? (blue) zse40(f) ise40- -22(l)-(m) with analog output zse40(f) ise40- -62(l)-(m) with analog output zse40(f) ise40- -30(l)-(m) with auto shift input zse40(f) ise40- -70(l)-(m) with auto shift input main circuit 1 k ? 12 to 24 vdc dc (+) (brown) analog output (gray) out1 (black) out2 (white) dc (? (blue) main circuit 1.2 k ? 6.8 k ? load 12 to 24 vdc dc (+) (brown) a uto shift input (gray) out1 (black) out2 (white) dc (? (blue) load load load http://www..net/ datasheet pdf - http://www..net/
kpa out2 out1 set description led (green) led (red) switches the mode and set value. down button set button displays present pressure. displays each mode. displays error mode. 3 1/2-digit led switching of the mode and set value up button calibration procedures setting procedure auto preset initial setting zero clear key lock mode normal operation set ?utput mode? ?esponse time?and ?uto or manual mode? enter the set value of the pressure to perform switch output. automatically sets the pressure for the adsorption confirmation or supply pressure confirmation. adjusts the zero point of the atmospheric pressure. allows fine-tuning of the data set automatically by auto preset. mode is not switched, even if the button is pressed during operation. measured pressure is displayed and the switch operation begins. displays out1 output condition when it is on, the led is illuminated. displays out2 output condition. when it is on, the led is illuminated. switches to each mode and fixes the set value. manual pressure setting manual pressure setting 16-2-19 zse ise pse z i se3 ps z i se 1 2 zsp isa2 is zsm pf2 if data series zse40/ise40 high precision, digital pressure switch http://www..net/ datasheet pdf - http://www..net/
select the response time by pressing either button or button. ( ? 2.5 ms, ? ? 24 ms, ? 192 ms, ? 768 ms select among them.) press the ?et?button for more than 2 seconds until ? ?is displayed. release it when the display turns to ? ? calibration procedures initial setting unit mode: when using a product with a unit switching function, refer to the next page for unit-setting (for overseas). 1. initial condition mode 2. selection of output mode out1 3. selection of output mode out2 set press the ?et button. press the ?et button. press the ?et button. 4. selection of response time 5. setting auto/manual press the ?et button to complete the setting. set set set select the ?utput mode?for out1 by pressing either but- ton or button. ? ?normally open mode ? ?normally closed mode select ?uto preset mode?or ?anual set mode?by pressing either button or button. ? ?auto preset mode ? ?manual set mode select the ?utput mode?for out2 by pressing either button or button. ? ?normally open mode ? ?normally closed mode button: increases set value button: decreases set value displays the set values ? ? or ? ? alternately. ? only for zse40(f)/ise40- -30/70(l)-m, displays the input mode ? ?and the compensation value alternately. if auto shift input is not complete, zero is displayed. select the manual set mode in the initial condition mode and press the ?et?button until ? ? or ? ? is displayed. manual pressure setting output mode differs by the pressure set value. press the ?et button. 1. manual set mode 2. input set point value for out1 (1) 3. input set point value for out1 (2) set press the ?et button. press the ?et button. press the ?et button. 4. input set point value for out2 (1) 5. input set point value for out2 (2) set set set 6. display of setting auto shift press the ?et?button to complete the setting. set button: increases set value button: decreases set value displays the set values ? ? or ? ? alternately. button: increases set value button: decreases set value displays the set values ? ? or ? ? alternately. button: increases set value button: decreases set value displays the set values ? ? or ? ? alternately. 16-2-20 series zse40/ise40 http://www..net/ datasheet pdf - http://www..net/
prepare the equipment for use under operating conditions. when setting out1 is not required, press both the b utton and b utton simultaneously in this state to skip to ? ? select the auto preset mode in the initial setting mode and press the ?et button until ? is displayed. a uto preset (for adsorption confirmation) wo r kpiece 1 wo rk piece 2 wo r kpiece 1 wo r kpiece 2 wo r kpiece n on = a off = b + a ?b 4 a ?b 4 wo r kpiece n high v acuum max. a on off min. b atmosphere suction released max. a: max. pressure value when a workpiece is adsorbed. min. b: min. pressure value when a workpiece is not adsorbed. press the ?et button. 1. auto preset mode 2. preparation for auto preset 3. auto preset of out1 set press the ?et button. 4. preparation for auto preset press the ?et button. 5. auto preset of out2 press the ?et button to complete the setting. set set set repeat adsorption and non- adsorption release several times in this state. the optimal set value is determined automatically. supplies vacuum pressure, changing the condition of a wo r kpiece by adsorption nozzle, etc. when setting out2 is not required, press both the b utton and b utton simultaneously in this state to skip to the measurement mode. repeat adsorption and non- adsorption several times in this state. the optimum set value is determined automatically. unit set yes no yes no [p] [n] out1 output mode p-1 p-2 p-2 n-1 n-2 n-1 n-2 h h h h h (fixed hysteresis) = 3 digits h (fixed hysteresis) = 3 digits ? out2: same as out1. off on high pressure (for positive pressure/compound pressure) high vacuum (for vacuum pressure) high pressure (for positive pressure/compound pressure) high vacuum (for vacuum pressure) high pressure (for positive pressure/compound pressure) high vacuum (for vacuum pressure) high pressure (for positive pressure/compound pressure) high vacuum (for vacuum pressure) off on off on off on window comparator mode hysteresis mode window comparator mode output type p-1 unit selection out1: selection of the output mode press ?et?button. set it's only subject to zse40(f)/ise40- - (l). set the unit by either button or button. : kpa or mpa, : kgf/cm 2 , : bar, : psi, : inhg, : mmhg hysteresis mode 16-2-21 zse ise pse z i se3 ps z i se 1 2 zsp isa2 is zsm pf2 if data series zse40/ise40 high precision, digital pressure switch http://www..net/ datasheet pdf - http://www..net/
prepare the equipment for use under operating conditions. when setting out1 is not required, press both the b utton and b utton simultaneously in this state to skip to ? ? select the auto preset mode in the initial setting mode and press the ?et button until ? is displayed. a uto preset (in the case of confirming the supply pressure) on point = c, c1 off point = c-3 digits, c1-3 digits (1 digit is the minimum setting unit.) on point (c, c1) off hysteresis (3 digits) press the ?et button. 1. auto preset mode 2. preparation for auto preset 3. auto preset of out1 set press the ?et button. 4. preparation for auto preset press the ?et button. 5. auto preset of out2 set set set prepare the equipment for use under operating conditions of out2. when setting out2 is not required, press both the b utton and b utton simultaneously in this state to skip to the measurement mode. the pressure is read and the optimal set value is determind automatically. the pressure is read and the optimal set value is determind automatically. press the ?et button for 4 seconds or longer. release it when the display turns to ? ? press the ?et button for 4 seconds or longer. release it when the display turns to ? ? display ? by pressing b utton or button. display ? by pressing b utton or button. calibration procedures other functions initiate key lock key lock mode release key lock set set p eak mode used to avoid a malfunction when buttons on the front part of the switch are pressed. bottom mode zero clear while displayed, pressing the b utton for 1 second or longer causes the peak mode to display and blink. pressing the button once again for 1 second or longer reinstates it. note) displaying the peak and the bottom display is not distinguished. pressing the + b uttons simultaneously with the supply pressure released to the atmosphere, causes it to reset to zero on the display and completes the zero clear operation. the function then returns to the measurement mode. while displayed, pressing the b utton for 1 second or longer causes the bottom mode to display and blink. pressing the button once again for 1 second or longer reinstates it. note) displaying the peak and the bottom display is not distinguished. allows an adjust to zero on the display if the pressure to be measured is within a range of 70 digits from the atmospheric pressure. press the ?et button to complete the setting. press the ?et button to complete the setting. press the ?et button to complete the setting. allows holding of the maximum pressure v alue on display under measurement. allows holding of the minimum pressure v alue on display under measurement. 16-2-22 series zse40/ise40 http://www..net/ datasheet pdf - http://www..net/
dimensions zse40(f)/ise40- 01 t1 mpa out2 out1 set atmospheric release port 30 30 600 (3000) lead wire length ?.5 18.35 6.4 2-m3 x 0.5 thread depth 4 m5 x 0.8 thread depth 5 width across flats 12 20 20 01: r 1/8 t1: npt 1/8 7.8 1.5 4.5 30 14 2.5 15.2 10.7 2.6 7 12.4 zse40(f)/ise40-w1 mpa out2 out1 set 30 30 600 (3000) lead wire length atmospheric release port 7 19 18.35 ?.5 6.4 rc 1/8 2-m4 x 0.7 thread depth 4 20 20 6.5 r rc 1/8 12 42 4 10.7 15.2 30 2.5 6 7.8 2.6 7 12.4 ? f or splash proof use (ip65), insert an air tube into the atmospheric release port. (refer to ?recautions on page 16-2-24 for details.) ? f or splash proof use (ip65), insert an air tube into the atmospheric release port. (refer to ?recautions on page 16-2-24 for details.) 16-2-23 zse ise pse z i se3 ps z i se 1 2 zsp isa2 is zsm pf2 if data series zse40/ise40 high precision, digital pressure switch http://www..net/ datasheet pdf - http://www..net/
dimensions caution 1. immediately after supplying power, there is drift of about 0.5% f.s. when used with very low pressure, allow the unit to warm up for about 20 to 30 minutes. 2. do not use in locations where there is splashing or spraying of oils and solvents. 3. when using a commercially available switching regulator, be sure to ground the fg terminal. 4. in locations where the switch is exposed to water and dust, etc., these may enter the switch from the atmospheric release port. insert ? tubing (inside diameter ?.5) into the atmospheric release port, and extend the other end to a safe area where water, etc., is not splashed or sprayed. be sure that tubing is not bent and holes are not blocked, etc., or it will become impossible to make correct pressure measurements. air tube recommended tubing (smc) tu0425 (polyurethane) atmospheric release port f or m5 zse40 ( f ) /ise40 c4 c6 m5 precautions set out1 out2 mpa 600 (3000) lead wire length 32.3 44.3 28.15 22.15 20 30 30 2-4.5 atmospheric release port 6.4 25.4 12.8 8 ?.5 18.35 19 one-touch fitting ?, ? 7 12 43 2.5 30 15.2 10.7 7.8 2.6 7 12.4 m5 x 0.8 thread depth 5 8.5 mpa out2 out1 set ? f or splash proof use (ip65), insert an air tube into the atmospheric release port. (refer to ?recautions for details.) 16-2-24 series zse40/ise40 http://www..net/ datasheet pdf - http://www..net/
|
